With the advancement of society and the development of the economy, science and technology are constantly developing. What is a puncher? The punching machine is completed by four major parts to complete the punching process. First, the material is moved to the scanning area of ​​the automatic punching machine camera. After the camera scans the image, it processes and gives the control part signal. After the control part receives the signal, it further processes and controls the movement of the transmission part to make the punch X on the plane. The shaft and the Y-axis move, and after the completion of the movement, the pneumatic part starts to work, and the solenoid valve controls the cylinder to perform the punching action. The automatic punching machine prints the positioning hole, and the whole action is completed in one go, fast, accurate and high efficiency.
　　 Machine Performance Editing Bag Punching Machine is mainly used in packaging factories, plastic bag factories, round holes, triangular holes, tearing holes, shaped holes, butterfly holes and so on.
Product classification editing 1, large round hole plastic bag pneumatic drilling machine: 12~80mm
2, the bill sawtooth hole punching machine: 4.0mm
3, the bill round hole punching machine: 4.0mm
4, butterfly hole plastic bag pneumatic punching machine: 25X6X9 30X6X9 32X6X9 30X6X8.5 32X5.5X11 35X7.5X12 160X14X4
5, aircraft hole pneumatic drilling machine: 20X10X5 30X12X6 32X12X6 34X9X4 37.3X16X9.1
6, hand hole / hand hole hole pneumatic punching machine: 68x18 70x22 80x20 70x22X17.5 76X16 85X30
7, tearing hole (tearing / easy to tear) pneumatic drilling machine (tearing / easy tearing): 4X2 5X2 7X3 9X2
8, triangular hole pneumatic drilling machine: 25X8 30X10.5 32X10 38X10 50X40 70X60
9, special-shaped hole pneumatic drilling machine: elliptical hole chamfer hole trapezoidal hole polygon four-pointed star tangential hole does not cut the trimming hole
10, the overall shaped bag pneumatic punching machine: square hole shaped mobile phone bag punching machine shaped cosmetic bag punching machine shaped jewelry bag punching machine
Operation Method Editing 1. Select the punching and punching die for the required aperture. Installed on the host die.
2. Insert the workpiece into the die, the opening, align the scribe line, and rotate the die to clamp.
3. Shake the handle and press the punch down to punch the hole.
Note Editing 1. Check whether the punch and die are matched before operation, otherwise the host will be damaged.
2. Before punching, the die must be screwed tightly.
3. If abnormal faults are found during operation, the punching should be stopped and the fault should be eliminated to avoid damage to the machine.
4. The screw and the nut should be lubricated with oil.
Daily maintenance editor Tianyang mold reminder: the punching machine should be cleaned frequently, play less dust, the most important thing is to ventilate heat, look at the temperature of the machine in time.
Common fault editing one, the punch is not going up, the air pressure is adjusted to 4-5MPa
2, the punch machine punch up 0.5MM position, so that the punch punch punch down to a shallow point. Second, hit a flash or can not beat: first use the gold steel set down the mold for about five or six minutes, then It can be rubbed with oil stone for two or three minutes. If there is still a flash on this method, please contact the manufacturer of the puncher. Third, the plastic bag will be pulled when punching: 1. Check if the air pressure is low.
2. Check if the punching signal system is normal.
3. Check if the puncher and the cutter are in sync
　　 The above is about the introduction of the bag punching machine, I hope to help everyone.
Dog Bath Foam.
Dog Bath Foam
DongGuan Lucky Pet Products Co., Ltd. , https://www.dgluckypet.com